Getting Familiar with Plumbing: A Must for Bathtub Installation
Getting Familiar with Plumbing: A Must for Bathtub Installation
Blog Article
This great article in the next paragraphs on the subject of How to Install a Bathtub Yourself is totally compelling. Read it yourself and decide what you think about it.
Setting up a tub isn't exactly rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently accessible, the project can relocate easily; if you need to open up a wall to get rid of the old tub and also position the brand-new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will need a helper to vacate the old tub and also set in the new one. Make sure you have qualified yourself for the task and also fit attempting it. As opposed to hiring a contractor to take control of a halfway-completed project, it is better to consider employing one prior to you start. Possibilities are you might require a specialist plumber to make tube connections.
This post will certainly assist you set up a brand-new bath tub in your bathroom if you have currently purchased a brand-new bathtub and also do not require to transform the plan of your previous water pipelines.
Your devices and also material checklist ought to make up the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you should do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather bothersome as a result of the limited access that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will come from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Before going on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location in between the tap and the sink. Protect the tap in position with the manufacturer offered backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet adapters. The former kind must be connected to the tap finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Tub
Using the two wooden boards under its feet, position the bath tub in the required placement. The wood boards are valuable in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the bathtub up until the spirit level checks out degree.
To set up taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Turn on the water supply as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if necessary. Load the bathtub as well as likewise examine the overflow outlet and also the typical outlet for leaks.
Lastly, fix the bathroom paneling as explained in the supplier's instruction manual. Tiling and also securing around the bath tub should wait till the bath tub has been used a minimum of once as this will certainly settle it right into its final placement.
Planning for the Installment
First of all, the supporting structure supplied with the bathroom needs to be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps device to prevent stress on the bath tub.
Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to split a stiff seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, leading to difficulties with wetness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your fixtures and fittings. They are sold in tubes and cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill up the bathtub with water before sealing, to enable the movement experienced when the bathtub remains in use. The sealant can fracture fairly early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily readily available on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Many thanks for taking the time to read our short article. Sharing is good. Who knows, you may be helping someone out. Thank you for taking the time to read it.
Prioritize plumbing safety. Report this page